GARDASOFT TR-HT2 Series User Manual Download Page 63

Page: 63 / 78

TR-HT2xx LED Controller - User Manual

flags (set using the

command)

current rating of the light after being sensed

successfully by SafeSense.

rating of the light (set by the

command).

When using Ethernet commands, use the following forms of the

command:

ST0

This reports the general settings. A typical reply to this command
might be:

TM 1, TP 20.00ms

Where:

Trigger status. 1 = on, 0 = off.

Trigger period.

STc

This reports the settings for a single channel, where

is the input

channel.

Simulate an input trigger

TRc

This command simulates an input trigger, where

is the input

channel. If the TR-HT is in pulse mode, it pulses the output once.

Enable Ethernet messages

This command enables or disables Ethernet messages. Type in:

GTm

Where:

= 0 to disable Ethernet messages

= 1 to enable Ethernet messages.

When Ethernet messages are enabled, any error reports are sent to
the most recent UDP or TCP/IP address from which a command
has been received. These messages take the form:

Evtc,e

Where:

= the channel number (zero for no channel)

= the event value, see

Section 13.2.5, Event

codes

—

Summary of Contents for TR-HT2 Series















































































Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands

GARDASOFT TR-HT2 Series, User Manual

Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands