GARDASOFT TR-HT2 Series User Manual Download Page 74

Page: 74 / 78

TR-HT2xx LED Controller - User Manual

Event number

Reason

1 to 127

An error has occurred. See Section 13.2.6, Error
codes.

128

A light has been connected and is working.

129

A light has been connected but does not have a
current or voltage rating.

130

An over temperature error has occurred.

131

An over current error has occurred.

132

An error has occurred while autosensing the rating
of a light.

138

SafePower trainup has completed.

139

SafePower trainup has failed or been cancelled.

140

In switched mode, the light has been turned off
because the duty cycle is too high.

13.2.6 Error codes

Some error codes are displayed on the TR-HT's front panel: these are also
shown.

Error number

Reason

Err 1

A parameter value is invalid.

Err 2

Command not recognised.

Err 3

A numeric value is in the wrong format.

Err 4

Wrong number of parameters.

Err 5

This is a warning, not an error. One of the
parameters is out of range and the value of that
parameter has been adjusted. For example,
sending an

command with a delay of 0μs returns

an ‘Err 5’. The command is accepted, but the delay
is set to the minimum allowed value.

—

Summary of Contents for TR-HT2 Series















































































Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands

GARDASOFT TR-HT2 Series, User Manual

Search results

Summary of Contents for TR-HT2 Series

Reviews:

Related manuals for TR-HT2 Series

Brands by name

Popular brands