GARDASOFT TR-HT2 Series User Manual Download Page 64 | Manualshive

Page: 64 / 78

background image

TR-HT2xx LED Controller - User Manual

Clear any errors

Use this command to read the last event or error code when
Ethernet messaging has been disabled:

GR

Any error displayed on the TR-HT is cleared. If this was a lighting
error, the unit resumes auto-sensing. If there are no outstanding
events or errors, the ‘

>

’ prompt is returned.

Set/Clear the webpage password

This command sets the webpage password. Up to six characters
can be chosen. Type in:

EYasc1,asc2,asc3,asc4,asc5,asc6

Where:

asc1

to

asc6

are decimal ASCII values for the letters of your

password

For example, a value of 65 is ‘A’, 66 is ‘B’ and so on up to 90 for ‘Z’.

Note:

When you use this password to access the TR-HT through the

webpage, you must use the actual characters and not the ASCII
values. Use upper case characters and do not enter commas or
spaces.

EY

Typing in

EY

on its own clears the password.

Disable the keypad

You may find it necessary to lock the front panel keypad to prevent
any unauthorised changes to the settings to the TR-HT. To disable
the keypad, type in the following command:

KBd,c

Where:

d

=

0 to enable the keypad

1 to disable the keypad but allow the unlock code

2 to disable the keypad and disallow the unlock code

c

=

the unlock code ( a number between 0 and 255).

You can still access the TR-HT’s settings using Ethernet commands
and through its web page. The settings of this command are
restored after a power cycle.

—

64

—

«
...
62
63
64
65
66
...
»

Summary of Contents for TR-HT2 Series















































































Reviews:

No comments

Related manuals for TR-HT2 Series

Brand: Hamworthy Pages: 10

Brand: BADODOSECURITY Pages: 8

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: Lattice Pages: 23

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: Parker Pages: 21

Brand: Parker Pages: 26

Brand: Parallax Pages: 3

Brand: Vageo Pages: 2

Brand: Vega Pages: 20

Brand: J+J Pages: 4

Brand: Val Controls Pages: 6

Brand: National Instruments Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands