background image

GAT ECO.Lock 7xxx F/ISO 
Technical Data

 

 
 

50             

HB_GAT-ECOLock-7xxxFISO--EN_12  

 

 

www.gantner.com

 

7.5  Interface 

 

Interface type: 

USB 2.0

 

Interface connection: 

USB type Micro-B 

 

7.6  Housing 

 

Material: 

Plastic (PC), halogen-free, V0

 

Color: 

Dark gray 

Weight: 

Approx. 400 g (14.1 oz.) 

Dimensions: 

109 mm x 109 mm x 33 mm (4.3´´ x 4.3´´ x 1.3´´) 

Break-in resistance capability: 

DIN 4547-2 class C 

 

7.7  Environmental Conditions 

 

Permitted ambient temperature 

- Indoor model: 

0 °C to 55 °C (32 °F to 131 °F) 

- Outdoor model: 

-25 °C to 55 °C (-13 °F to 131 °F) 

Protection type 

 

- Indoor model: 

IP 52 (when installed) 

- Outdoor model: 

IP 64 (when installed and locked) 

Environment class based on VdS 2110 

 

- Indoor model: 

II (conditions in indoor areas) 

- Outdoor model: 

III (conditions in outdoor areas) 

Compliance: 

CE 

 
 
 
 
 
 
 
                                                                                                                     _ 

Note: 

This manual is valid from June 4

th

, 2018. It is subject to change. 

Amendments can be made without prior notice at any time.

 

 

 

Summary of Contents for Mifare Gat ECO.Lock 7 F/ISO Series





















































Reviews: