background image

GAT ECO.Lock 7xxx F/ISO 
Operation

 

 
 

34             

HB_GAT-ECOLock-7xxxFISO--EN_12  

 

 

www.gantner.com

 

5.2.3  Free Locker Unique Number Mode 

 

“Free locker unique number” operating mode differs from the standard free locker mode in the following ways: 

All MIFARE and ISO 15693 data carriers can operate with the lock. 

The data carrier can have a GANTNER locker segment, however the segment is not used for this mode. 

When a locker is locked with a data carrier, the locker number is not written onto the data carrier. 

Every data carrier can use (lock) any number of lockers at the same time. 

 
Locking and unlocking lockers 
 

►  Close the locker door and hold it shut. 
►  Press the button of the GAT ECO.Lock 7xxx F/ISO in using a data carrier for approximately 1 second. 

o

  The information on the data carrier is read. 

►  a)  Valid data carriers: The LED flashes green briefly and the locking action is carried out. 
  

b)  Invalid data carriers: The LED flashes red briefly and the GAT ECO.Lock 7xxx F/ISO does not complete the 

locking action. 

►  Release the locker door.  

 
 
 

5.2.4  Personal Locker Programming Card Mode 

 

For lockers operating in “personal locker programming card” mode, up to 32 data carriers per GAT ECO.Lock 7xxx 
F/ISO can be authorized for use. The data carriers can be used with the locker as often as required and share the 
same authorization access, e.g., family cards.    
The data carriers are authorized for use with the personal locker using the “program” data carrier (included in the 
GAT ECO.Basic Set F/ISO, see section “5.3. GAT ECO.Basic Set F/ISO”).  

 

Authorizing data carriers 

       

►  Close the locker door and hold it shut. 
►  Press the button of the GAT ECO.Lock 7xxx F/ISO in using the program data carrier for approximately 1 

second. 

o

  The information on the data carrier is read. 

►  The GAT ECO.Lock 7xxx F/ISO enters into programming mode.  

o

  The LED ring flashes red until the program data carrier is removed. As soon as the program data 

carrier has been removed, the LED ring flashes red/green and the lock is ready to program data 
carriers. 

►  Within 5 seconds, press the button of the GAT ECO.Lock 7xxx F/ISO in for approximately 1 second using the 

data carrier to be authorized. 

►  a)  Successful authorization: The LED flashes green for approximately 3 seconds. When the data carrier is 

removed, the LED flashes green and red alternately again and another data carrier can be authorized in the 

same way. Repeat this process until all the data carriers are authorized. 

  

b)  Unsuccessful authorization: The LED flashes red three times then the GAT ECO.Lock 7xxx F/ISO switches 

off. Possible reasons for this include: 

-  The maximum of 32 data carriers are already authorized for use with the lock. 
-  The data carrier was not read by the lock correctly, e.g., the button was not pressed in for long enough or 

the data carrier is damaged. 

 

Summary of Contents for Mifare Gat ECO.Lock 7 F/ISO Series





















































Reviews: