background image

GAT ECO.Lock 7xxx F/ISO 
Technical Data

 

 

www.gantner.com

 

                                                                                 HB_GAT-ECOLock-7xxxFISO--EN_12

 

49

 

 

7

 

TECHNICAL DATA 

 
 

7.1  Power Supply 

 

Power supply:

 

3 x 1.5 V alkaline* batteries, type AA  

*lithium batteries can also be used

 

GANTNER approved battery: 

Batterie 1.5V Alkali AA (Part No. 308819)

 

Battery lifetime: 

Up to 5 years* or 30,000 cycles with alkaline batteries at room 
temperature

 

depending on usage, configuration, and ambient conditions

 

 

7.2  Reading Field 

 

Reader type:

 

MIFARE

®

 supported types: 

 

  - MIFARE

® 

Classic (1k and 4k) 

 

  - MIFARE Ultralight

® 

 

  - DESFire EV1

® 

and EV2

® 

 

- ISO 15693 

Note: It is recommended to have customer-specific data carriers approved by 
GANTNER before use 

Reading field frequency: 

13.56 MHz 

Reading field range: 

5 to 35 mm (0.2´´ to 1.38´´)* 

 

*

depending on the installation and type of data carrier 

 

7.3  Memory and Time Management 

 

Data storage: 

EEPROM with capacity for 150 bookings, data retained during battery 
change 

 

Internal clock: 

Quartz-controlled, real-time clock 

 

7.4  Control and Display Elements 

 

Control element: 

Button 

 

Display element: 

LED ring (multi-colored) for status indication 

 

Summary of Contents for Mifare Gat ECO.Lock 7 F/ISO Series





















































Reviews: