manualshive.com logo in svg

Fujitsu FI-5900C, Operator'S Manual

Share
Download
Fujitsu FI-5900C Operator'S Manual Download Page 231

211

8.21 Auto Color Detection

8

SCANNER SETTINGS

8.21 Auto Color Detection

You can adjust the slice level for auto color detection.

Configure the settings for the Auto Color Detection as follows:

1.

Start up the Software Operation Panel.

Refer to 

“8.1 Scanner Settings” on page 177

.

2.

Select [Device Setting 2] from left side list in the window, and select [Auto 
color Detection] from its lower level.

 

3.

Select the Slice value.

You can select the Slice value from 1 to 255 (255 levels).
In the case that black and white documents are judged as color documents, select larger values.
In the case that color documents are judged as black and white, select smaller values.

HINT

The auto color detection setting can be configured on the scanner driver 
setting window.
For details on how to set the setting, refer to 

“3.11 Color/monochrome Auto 

Detection” on page 96

.

Summary of Contents for FI-5900C


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands