manualshive.com logo in svg

Fujitsu FI-5900C, Operator'S Manual

Share
Download
Fujitsu FI-5900C Operator'S Manual Download Page 116

96

3.11 Color/monochrome Auto Detection

3.11 Color/monochrome Auto Detection

The scanner detects whether the scanned document is color or binary monochrome. According to this detection, the 
images will be output in color (or grey scale) for colored documents, ide binary black and white for monochrome 
documents.

*Depending on the application, this function may not operate properly.   

The settings for MultiStream can be done on the Scanner Driver.

The following operation uses the TWAIN driver.

1.

Start up TWAIN driver from the application you are using

Refer to 

“2.13 How to use the Scanner Driver” on page 41

.

2.

Please check the [Enable Multi Image] checkbox in the [TWAIN Driver] window.

* When [Long Page..] is specified at [Scan Type:], you can not check this checkbox.

Main screen

Summary of Contents for FI-5900C


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands