manualshive.com logo in svg

Fujitsu FI-5900C, Operator'S Manual

Share
Download
Fujitsu FI-5900C Operator'S Manual Download Page 91

71

3.3 Scanning Documents with different widths

3

SCANNI

NG V

A

RIOUS TYPES OF DOC-

3.3 Scanning Documents with different 

widths

When you scan a batch of documents with different widths, follow the instruction below. 

1.

Align the leading edge of the documents.

 

This section describes the procedure to align the document alongside their center line.
For the procedure to align the document with its left (or right) edge, refer to 

“ (2)Setting the 

document by either Side Guide of the hopper.” on page 19

.

2.

Load the documents on the center of the hopper. 

  

Aligning the document  

alongside their center line

Aligning the document

with its left (or right) edge  

Pick roller

Summary of Contents for FI-5900C


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands