manualshive.com logo in svg

Fujitsu FI-5900C, Operator'S Manual

Share
Download
Fujitsu FI-5900C Operator'S Manual Download Page 166

146

6.3 Troubleshooting

(*1)

Refer to 

fi-5900C Getting Stated,  “2.2 Connecting the scanner to your PC”.

NO

YES

YES

NO

NO

Are the documents loaded correctly 
onto the hopper?

Is the ADF cover closed completely?

Load the documents correcty.

Close ADF cover completely.

Is the interface cable connected
correctly?

Connect the interface cable
correctly.
(*1)

Symptom 3

The scanning does not start.

YES

㧨

When using the SCSI interface

㧪

Is the SCSI ID set correctly?

YES

Set the SCSI ID correctly
and restart the scanner and PC.
(*1)

NO

Does the scanning start after turning
the scanner on again?

NO

The scanner operation is 
normal.

YES

If the problem can not be resolved with this flowchart, refer to  
"6.4 Before Contacting a Service Provider."
After checking the items given in section 6.4, contact an authorized  
FUJITSU scanner service provider or your dealer. 

Summary of Contents for FI-5900C


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands