Fujitsu FI-5900C Operator'S Manual Download

Page: 241 / 257

221

8.29 Pause scanning

SCANNER SETTINGS

Select one of the following options and click the [OK] button.

<Pause/Resume>

If this setting is enabled, scan is suspended/restarted in the following operation.

Pause

•

Press the [Send to] button during scan operation.

Resume

•

Press the [Scan] button while scan operation is suspended.

•

Remove all documents on the Hopper and in the transport path.

(Scanning operation is resumed from the status when the message “Load Paper“ is dis-
played.)

Disable : Disables the pause scanning.

Enable

: Enables the pause scanning.

ATTENTION

•

This function is disabled in manual feeding mode.

•

Do not switch the feeding mode to the manual feeding, or change the
Pause scanning to [Disable].

•

Pause scanning function is enabled from the second sheet of the batch

or later after scan starts.

•

Pausing the scanning operation is possible at a position where scan-
ning can be resumed. For this reason, if there is a document in the
transport path, scanning is paused after the document is scanned.

Summary of Contents for FI-5900C


































































































































































































































































Search results

Summary of Contents for FI-5900C

Reviews:

Related manuals for FI-5900C

Brands by name

Popular brands

Fujitsu FI-5900C, Operator'S Manual

Search results

Summary of Contents for FI-5900C

Reviews:

Related manuals for FI-5900C

Brands by name

Popular brands