manualshive.com logo in svg

Fujitsu FI-5900C, Operator'S Manual

Share
Download
Fujitsu FI-5900C Operator'S Manual Download Page 135

115

4.4 Cleaning the Rollers (with a lint-free cloth)

4

DA
IL

Y

 C
A

R

E

4.

Clean the Pick roller and the rubber surface of the Separator rollers using 
the cleaner F1.

 

5.

Close the roller cover after the cleaning is finished.

6.

Open the Pad cover.

Grab both sides of the cover, press to the inside and pull down (towards you), as shown in the 
illustration below.

 

ATTENTION

It may take long before the cleaner vaporizes if a large quantity is used. 
When cleaning the scanner parts, dampen a cloth with modest quantities 
of the cleaner. In addition, wipe off the cleaner completely with a soft lint-
free cloth to leave no residue on the surface of the cleaned parts. 

Separator roller

Pick roller

Roller cover

Pad cover 

Summary of Contents for FI-5900C


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands