background image

Float Switch Information

The SJE Rhombus Signalmaster float switch  is pre-mounted in Fuji Clean USA treatment systems.  This 
information from SJE Rhombus is supplied for informed, proper handling during the installation process.

38

ELECTRICAL SHOCK HAZARD
Disconnect power before installing or servicing this 
product.  A qualified service person must install and 
service this product according to applicable electrical 
and plumbing codes.

EXPLOSION OR FIRE HAZARD
Do not use this product with flammable liquids.  Do not 
install in hazardous locations as defined by National 
Electric Code, ANSI/NFPA 70.

Failure to follow these precautions could result in serious injury or death.  Replace product immediately if switch becomes damaged or severed.  Keep 
these instructions with warranty after installation.   This product must be installed in accordance with National Electric Code, ANSI/NFPA 70 so as to 
prevent moisture from entering or accumulating with in boxes, conduit bodies, fittings, float housing, or cable.

PREVENTATIVE MAINTENANCE

Periodically check the product.  Check that the cable has not become worn or that the housing has not been damaged so as to impair the protection 
of the product.  Replace the product immediately if any damage is found or suspected.

Periodically check to see that the float is free to move and operate the switch.

Use only SJE Rhombus replacement parts.

The Sensor Float and Sensor Float Mini control switches contain mercury and MUST be recycle or disposed of according to local, state and federal 
codes.

Summary of Contents for CE6KG
















































Reviews: