Fuji Xerox ApeosPort C5570 Reference Manual Download Page 183

Page: 183 / 290

183

8.1 Replacing Consumables

While grasping the lever of the staple cartridge, push the staple cartridge into its original position until it clicks
into place.

Close the finisher front cover.

Replacing the booklet staple cartridge (when Finisher-B3
booklet unit is installed)

A message appears on the touch panel display according to the remaining amount of staples.

Note



Before replacing the booklet staple cartridge, tap [Device] > [Supplies] on the Home screen and check the status of the
booklet staple cartridge.

Make sure that the device is not operating, and open the finisher side cover.

Hold the tabs on both sides of the staple cartridge and pull the cartridge out of the finisher.

Summary of Contents for ApeosPort C5570



































































































































































































































































































Search results

Summary of Contents for ApeosPort C5570

Reviews:

Related manuals for ApeosPort C5570

Brands by name

Popular brands

Fuji Xerox ApeosPort C5570, Reference Manual

Search results

Summary of Contents for ApeosPort C5570

Reviews:

Related manuals for ApeosPort C5570

Brands by name

Popular brands