41
EN-US
General
Safety
Setup Regula-
tions
The power sources have been tested according to degree of protection IP 23. This means:
-
Protection against solid foreign bodies larger than Ø 12 mm (0.47 in.)
-
Protection against spraywater up to an inclined angle of 60°
With its IP 23 degree of protection, the welding system can be set up and operated out-
doors. The effects of direct moisture (from rain, for example) are to be avoided, however.
The ventilation channel for the power sources is an important safety device. When select-
ing the setup location, ensure that the cooling air can enter and exit unhindered through
the vent on the front and back. Any electrically conductive dust (e.g. from grinding work)
must not be allowed to be sucked directly into the system.
Grid Connection
The device is designed for the grid voltage stated on the rating plate. The fuse protection
required for the grid lead can be found in "Technical Data." If mains cables or mains plugs
are not included with your version of the appliance, attach the appropriate mains cable or
mains plug in accordance with your country's standards.
Set Up LaserHy-
brid Welding Sys-
tem
Initial situation:
Robot and robot control are present and ready for operation
Set up welding system:
Install upright brackets
Install cooling unit on upright bracket
Connect power source to cooling unit
Set up welding wire drum
Assemble WF Mounting Drum on welding wire drum
Set up and connect wirefeeder reel
WARNING!
Work performed incorrectly can cause serious injury and damage to
property. This setting work must only be carried out by trained and qualified per-
sonnel. Please observe the safety rules in the Operating Instructions, and the
"Safety Inspection" section in particular.
WARNING!
Toppling or falling devices can be deadly. Securely set up the devic-
es on a level and stable surface.
NOTE!
An under-dimensioned electrical installation can lead to serious damage.
The grid lead and its fuse protection should be designed to suit the existing power
supply. The technical data on the rating plate should be followed.
WARNING!
If a power source is connected to the grid during installation, there is
a danger of serious injury and damage. Please read the information in the "Safety
Rules" chapter in the Operating Instructions for the power source before starting
for the first time. Only perform all of the preparation steps if
-
the power switch for the power source is set to – O – ,
-
the mains cable is disconnected from the grid.
1
2
3
4
5
6
Summary of Contents for LaserHybrid MHP 360i LH
