manualshive.com logo in svg

Freescale Semiconductor MPC8250, Family Reference Manual

Share
Download
Freescale Semiconductor MPC8250 Family Reference Manual Download Page 1261

Serial Peripheral Interface (SPI)

MPC8260 PowerQUICC II Family Reference Manual, Rev. 2

Freescale Semiconductor

38-15

 

38.7.1.2

SPI Transmit BD (TxBD)

Data to be sent with the SPI is sent to the CP by arranging it in buffers referenced by TxBDs in the TxBD 
table. TxBD fields should be prepared before data is sent. The format of an TxBD is shown in 

Figure 38-12

.

 

Table 38-9

 describes the TxBD status and control fields.

4

L

Last. Updated by the SPI when the buffer is closed because SPISEL was negated (slave mode 
only). Otherwise, RxBD[ME] is set. The SPI updates L after received data is placed in the buffer.
0 This buffer does not contain the last character of the message.
1 This buffer contains the last character of the message. 

5

—

Reserved, should be cleared.

6

CM

Continuous mode. Master mode only; in slave mode, CM should be cleared.
0 Normal operation.
1 The CP does not clear RxBD[E] after this BD is closed; the buffer is overwritten when the CP next 

accesses this BD. This allows continuous reception from an SPI slave into one buffer for 
autoscanning of a serial A/D peripheral with no core overhead.

7–13

—

Reserved, should be cleared.

14

OV

Overrun. Set when a receiver overrun occurs during reception (slave mode only). The SPI updates 
OV after the received data is placed in the buffer.

15

ME

Multimaster error. Set when this buffer is closed because SPISEL was asserted when the SPI was 
in master mode. Indicates a synchronization problem between multiple masters on the SPI bus. The 
SPI updates ME after the received data is placed in the buffer.

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

0

R

—

W

I

L

—

CM

—

UN

ME

2

Data Length

4

Tx Buffer Pointer

6

Figure 38-12. SPI TxBD

Table 38-9. SPI TxBD Status and Control Field Descriptions

Bits

Name

Description

0

R

Ready.
0 The buffer is not ready to be sent. This BD or its buffer can be modified. The CP clears R (unless 

RxBD[CM] is set) after the buffer is sent (unless RxBD[CM] is set) or an error occurs.

1 The buffer is ready for transmission or is being sent. The BD cannot be modified once R is set.

1

—

Reserved, should be cleared.

Table 38-8. SPI RxBD Status and Control Field Descriptions (continued)

Bits

Name

Description

Summary of Contents for MPC8250

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands