manualshive.com logo in svg

Freescale Semiconductor MPC8250, Family Reference Manual

Share
Download
Freescale Semiconductor MPC8250 Family Reference Manual Download Page 1005

ATM Controller and AAL0, AAL1, and AAL5

MPC8260 PowerQUICC II Family Reference Manual, Rev. 2

Freescale Semiconductor

30-85

 

30.12.1.1 UTOPIA Master Multiple PHY Operation

The PowerQUICC II supports two polling modes:

•

Direct polling uses CLAV[3–0] with PHY selection using ADD[1–0]. Up to four PHYs can be 
supported. 

•

Single CLAV polling uses Clav and ADD[4–0]. ATM controller polls all active PHYs starting from 
PHY address 0x0 to the address written in FPSMR[LAST_PHY]. Up to 31 PHY devices are 
supported. 

Both modes support round-robin priority or fixed priority, described in 

Section 30.13.2, “FCC 

Protocol-Specific Mode Register (FPSMR).”

TxClav/TxCLAV[3–0] Transmit cell available. Asserted by the PHY device to indicate that the PHY has room for a 

complete cell.

TxPRTY 

Transmit parity. Asserted by the ATM controller. It is an odd parity bit over the TxDATA bits.

TxCLK 

Transmit clock. Provides the synchronization reference for the TxDATA, TxSOC, TxENB, 
TxCLAV, TxPRTY signals. All the above signals are sampled at low-to-high transitions of 
TxCLK.

TxADD[4–0]

Transmit address. Address bus from the ATM controller to the PHY device used to select the 
appropriate M-PHY device. Each M-PHY device needs to maintain its address. TxADD[4] is the 
msb.

RxDATA[15–0]/[7–0]

Carries receive data from the PHY to the ATM controller. RxDATA[15]/[7] is the msb when using 
UTOPIA 16/8, RxDATA[0] is the lsb. 

RxSOC

Receive start of cell. Asserted by the PHY device as the first byte of a cell is received on 
RxDATA.

RxENB

Receive enable. An ATM controller asserts to indicate that RxDATA and RxSOC will be sampled 
at the end of the next RxCLK cycle. For multiple PHYs, RxENB is used to three-state RxDATA 
and RxSOC at each PHY’s output. RxDATA and RxSOC should be enabled only in cycles after 
those with RxENB asserted.

RxClav/RxCLAV[3–0
]

Receive cell available. Asserted by a PHY device when it has a complete cell to give the ATM 
controller. 

RxPRTY

Receive parity. Asserted by the PHY device. It is an odd parity bit over the RxDATA. If there is 
a RxPRTY error and the receive parity check FPSMR[RxP] is cleared, the cell is discarded. See 

Section 30.13.2, “FCC Protocol-Specific Mode Register (FPSMR)

,” and 

Section 30.10.7, “UNI 

Statistics Table

.”

RxCLK 

Receiver clock. Synchronization reference for RxDATA, RxSOC, RxENB, RxCLAV, and 
RxPRTY, all of which are sampled at low-to-high transitions of RxCLK.

RxADD[4–0]

Receive address. Address bus from the ATM controller to the PHY device used to select the 
appropriate M-PHY device. Each M-PHY device needs to maintain its address. RxADD[4] is the 
msb.

Table 30-44. UTOPIA Master Mode Signal Descriptions (continued)

Signal Description

Summary of Contents for MPC8250

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands