fos4X Blackbird OECD MDE0835 Instructions For Use Manual Download Page 64

Page: 64 / 80

8. Troubleshooting

Problem

Possible cause

Solution

RUN-LED
on the CAN
connector flashes
continuously.

See

LEDs and

Switch on the CAN
Connector, page 21

Make sure that the Bus Master is
configured correctly.

Reboot the Blackbird OECD. Turn the
power supply off and on.

ERROR-LED on
the CAN connector
flashes.

See

LEDs and

Switch on the CAN
Connector, page 21

Make sure that the CAN Interface
is configured correctly. See

Commissioning the CAN Interface,
page 54

Make sure that the Bus Master is
configured correctly.

Make sure that the bit rate of the
CAN bus is configured correctly.

Check the CAN cable for damage.
Replace damaged cables.

Make sure that the CAN cable is
connected correctly.

Do a firmware update. See

Firmware Update, page 70

8.4.2 Troubleshooting CAN Object 0x2000

TIP

The number of the sub-object corresponds to the channel
number.

Table 47: Troubleshooting CAN Object 0x2000

Problem

Possible cause

Solution

64 / 80

MDE0835_4-10_1.3.x_5.0_Blackbird

OECD_(6CH, CNO)-en-us

Summary of Contents for Blackbird OECD MDE0835

















































































Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands

fos4X Blackbird OECD MDE0835, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands