fos4X Blackbird OECD MDE0835 Instructions For Use Manual Download Page 21

Page: 21 / 80

3. Product Description

Table 19: LED on the Ethernet connector.

State

Power-LED

Status-LED

Network connection present

Off

No network connection present

No network traffic

Flashing

Network traffic

3.4.1.4

LEDs and Switch on the CAN Connector

There are 3 LEDs on the CAN connector. One LED is not used.

Figure 7: LEDs and Switch on the CAN Connector

Switch for terminating resistor

Run-LED (green)

Error-LED (red)

LED not in use

Switch for terminating resistor

The CAN connector has a 120 Ohm terminating resistor. The terminating resistor can
be activated and deactivated via the switch (1). In the right position, the terminating
resistor is active.

Run-LED

Table 20: Run-LED on the CAN Connector

State

Device state

Description

Operational

■

After booting, if

auto-

operational

is active

■

Set by Bus-Master

MDE0835_4-10_1.3.x_5.0_Blackbird

OECD_(6CH, CNO)-en-us

21 / 80

Summary of Contents for Blackbird OECD MDE0835

















































































Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands

fos4X Blackbird OECD MDE0835, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands