fos4X Blackbird OECD MDE0835 Instructions For Use Manual Download Page 22

Page: 22 / 80

3. Product Description

State

Device state

Description

Slow flashing

Pre-Operational

■

After booting, if

auto-

operational

is not active

■

Set by Bus-Master

Single flash

Stopped

■

Set by Bus-Master

Double flash

Reserved for future assignment

Error-LED

Table 21: Error-LED on the CAN Connector

State

Device state

Description

Off

No error

Slow flashing

Invalid

Configuration

General configuration error

Single flash

Warning limit

reached

At least one error counter of the CAN
controller has reached or exceeded the
warning level.

Double flash

Error control

event

guard event

(NMT slave or NMT

master) or a

heartbeat event

(heartbeat consumer) has occured.

Triple flash

Sync error

The sync message was not received
within the configured time span for the
communication cycle

Bus off

Error with the connection to the CAN
controller

3.5 Software

3.5.1 Factory Settings

Table 22: Factory Settings

Parameter

Factory setting

Static

IP-address

192.168.39.99

22 / 80

MDE0835_4-10_1.3.x_5.0_Blackbird

OECD_(6CH, CNO)-en-us

Summary of Contents for Blackbird OECD MDE0835

















































































Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands

fos4X Blackbird OECD MDE0835, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands