fos4X Blackbird OECD MDE0835 Instructions For Use Manual Download Page 24

Page: 24 / 80

3. Product Description

3.5.2.1

Home

Figure 8: Home

Table 23: Home: Information on the home page

Section

Content

System Name

Set name of the system.

System Location

Set location of the system.

System State

Informations about the system state.

■

CAN

: Status of the CAN bus.

■

Signals

: Informations about the

measurement channels

■

Uptime

: Operating time of the system.

System Information

Informations about the system:

■

Device Type

: Type designation and version

of the Blackbird OECD.

■

Serial Number

: Serial number of the

Blackbird OECD.

■

Firmware Version

: Currently installed

firmware version.

24 / 80

MDE0835_4-10_1.3.x_5.0_Blackbird

OECD_(6CH, CNO)-en-us

Summary of Contents for Blackbird OECD MDE0835

















































































Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands

fos4X Blackbird OECD MDE0835, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands