manualshive.com logo in svg

Ford Falcon (FG) 2010, Manual

Share
Download
Ford Falcon (FG) 2010 Manual Download Page 217

-217-

Audio

7.5 

Media volume

This feature allows you to adjust the 
volume level of:

1. 

Sonar (reverse sensing system)

2.  Navigation

3.  Auxiliary/iPod

Turn the ICC Control Dial (2) clockwise to 
increase the media volume.

Turn the ICC Control Dial (2) 
counterclockwise to decrease the media 
volume.

8.    Radio SCAN/AS

(Audio > Radio Scan/AS)

8.1 

Scan active

Scan active provides an eight second 
preview of each tunable radio station 
within the entyre radio band.

To operate, ensure the system is in 
radio mode. Press the SCN/AS button 
(7) until the radio begins to scan the 
radio frequencies shown in the display 
window. 

Pressing SCN/AS during scanning will 
stop the scanning process. Within 
the 8 second window, the station can 
be manually stored to one of the six 
radio presets. Press one of the six 
multifunction buttons for longer than 
two seconds to store the station to the 
corresponding preset.

Press the OK button (12) to select Scan 
Active. This will deselect auto store and 
vice versa.

Summary of Contents for Falcon (FG) 2010









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands