manualshive.com logo in svg

Ford Falcon (FG) 2010, Manual

Share
Download
Ford Falcon (FG) 2010 Manual Download Page 190

-190-

Wheels and tyres

Tyre pressures

Tyre recommendations may vary from 
time to time. Refer to the tyre placard, 
located in the glove compartment, for 
the tyre pressures, load rating index and 
speed ratings applicable to your vehicle.

Tyre pressures for standard tyres

Tyre pressures (when tyres are cold)

Model

Tyre Size

Pressure kPa (psi)

Normal Load

Maximum Load

Front 

Rear

Front

Rear

XT

215/60 R16 95V

230 (33)   

230 (33)

240 (35)

250 (36)

G6, G6E 

235/50 R17 96V

210 (30) 

210 (30) 

240 (35) 

270 (39)

XR6 (E-Gas)

235/50 R17 96V

210 (30) 

210 (30) 

240 (35) 

270 (39)

XR6

245/45 R17 95W

210 (30) 

210 (30) 

240 (35)

270 (39)

XR6T

245/40 R18 93Y

230 (33) 

210 (30) 

250 (36) 

270 (39)

G6ET

245/40 R18 93Y

210 (30) 

210 (30) 

250 (36) 

270 (39)

Temp Spare

T155/80 R17 111M

420 (60) 

420 (60) 

420 (60) 

420 (60)

Tyre pressures for optional tyres

Tyre pressures (when tyres are cold)

Model

Tyre Size

Pressure kPa (psi)

Normal Load

Maximum Load

Front 

Rear

Front

Rear

XT

235/50 R17 96V

210 (30)

210 (30)

240 (35)

250 (36)

XR6T

245/45 R17 95W

210 (30)

210 (30)

240 (35)

270 (39)

G6, G6E

245/40 R18 93Y

210 (30)

210 (30)

250 (36)

270 (39)

XR6

245/40 R18 93Y

230 (33)

210 (30)

250( 36)

270( 39)

XR6T 

245/40 R18 XL 97Y

230 (33)

210 (30)

250 (36)

270 (39)

G6, G6E, 

G6ET, XR6, 

XR6T

245/35 R19 XL 93Y

260 (38)

260 (38)

290 (42)

290 (42)

XT

225/55R16 95W

210 (30)

210 (30)

240 (35)

250 (36)

Summary of Contents for Falcon (FG) 2010









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands