manualshive.com logo in svg

Flomotion Systems be6000 series, Installation And Operation Manual

Share
Download
Flomotion Systems be6000 series Installation And Operation Manual Download Page 39

BE6000 Ultrasonic Flow Meter O&M Manual 

Flomotion Systems, Inc. ~ FlomotionSystems.com

 

39

III. Trouble Shooting 

With highly reliable design, the BE6000 ultrasonic flowmeter has a low failure rate. However, problems may 
occur as a result of unskillful handling, setting errors or working in an extremely undesirable working 
condition. For this reason, the meter is equipped with a self-diagnostic function. Problems detected are 
displayed in time order in code form on the upper right corner of the LCT screen. Hardware malfunctions, 
though generally checked after power is on, can also be detected (part of them) while the device is working 
normally. Information about “stop working” problems caused by wrong settings or undesirable working 
conditions can also be displayed, so users can locate the problems quickly and solve the problems according 
to the solutions offered in the following two tables in time.  
 
There are two kinds of error displayed in BE6000:  
 

- 

Error messages are displayed during self-test after the power is switched on. After entering the 

measurement mode, if there is an error, “*F” will be displayed at the top left corner of the screen. Check the 
information being displayed and take specific steps according to the following tables. If problems persist, 
contact your BE6000 distributor. 
 

- 

Errors about the specific signal received or wrong settings can be displayed by the M08 

window in error code form. Errors and solutions are listed in the following tables; 
 

Power-On self-test information, Causes and Solutions 

 

LCD Display 

 

Causes 

 

Solution 

 

ROM Parity Error  

System ROM illegal or in error  

Contact the manufacturer.  

Stored Data Error  

Stored Data Error  

Restart the instrument or contact the 
manufacturer.  

Handshaking Error  

Hardware handle wrong, system will 
reset.  

Restart.  

SCPU Fatal Error  

Fatal error in sub CPU circuit  

Restart or contact the manufacturer.  

Timer Slow Error Timer Fast 
Error  

System clock is wrong.  

Contact the manufacturer.  

CPU or Interruption error, 
retry  

Main CPU is wrong.  

Restart  

System RAM Error  

System RAM has problems.  

Restart or contact the manufacturer.  

Time or Batt Error  

System time chip error  

Restart or contact the manufacturer.  

When pressing the keys, no 
response from screen, no 
display or disorderly display  

Mis-operation, poor cable contact on 
the panel  

Soft Reset. Check whether the cables 
on the panel are contacted well.  

PRN Time Over  

Printer wrong or wrong connection.  

Examine printer or cable.  

 

Summary of Contents for be6000 series
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands