Flomotion Systems be6000 series Installation And Operation Manual Download Page 33

Page: 33 / 47

BE6000 Ultrasonic Flow Meter O&M Manual

Flomotion Systems, Inc. ~ FlomotionSystems.com

3. Reverse Flow

12. Energy Pulse

4. AO over 100%

13. On/Off via RS232

5. FO over 120%

14. Fluid Changed

6. Alarm #1

15. Key Stroking On

7. Alarm #2

16. Not Using

8. Batch Control

•

OCT Output Setup (M78)

Set the system to put hardware OCT output when one of the following sources occurs;

0. No Signal

9. POS into Pulse

1. Poor Signal

10. NEG into Pulse

2. Not Ready(No*R)

11. NET into Pulse

3. Reverse Flow

12. Energy Pulse

4. AO over 100%

13. FO

5. FO over 120%

14. FO via RS232

6. Alarm #1

15. On/Off via RS232

7. Alarm #2

16. Fluid Changed

8. Batch Control

17. Not Using

•

Relay Output Setup (M79)

Set the system to put Relay output when one of the following sources occurs;

0. No Signal

8. Batch Control

1. Poor Signal

9. POS into Pulse

2. Not Ready(No*R)

10. NEG into Pulse

3. Reverse Flow

11. NET into Pulse

4. AO over 100%

12. Energy Pulse

5. FO over 120%

13. On/Off via RS232

6. Alarm #1

14. Fluid Change

7. Alarm #2

15. Not Using

•

Flow Batch Control Setup (M80)

Select the batch control type. Available options are as follows;

0. Key Input

4. AI2 Down Edge

1. AI1 Up Edge

5. AI3 Up Edge

2. AI1 Down Edge

6. AI3 Down Edge

3. AI2 Up Edge

7. AI4 Up Edge

OCT Output Setup [78

17. Not Using

Relay Output Setup [79

15. Not Using

Flow Batch CTRL in

0. Key Input

Summary of Contents for be6000 series
















































Search results

Summary of Contents for be6000 series

Reviews:

Brands by name

Popular brands

Flomotion Systems be6000 series, Installation And Operation Manual

Search results

Summary of Contents for be6000 series

Reviews:

Brands by name

Popular brands