Fayat Bomag BW 900-50 Service Manual Download Page 203

Page: 203 / 245

Do not operate the main battery switch under load.

Do not use jump leads after the battery has been removed.

Sensors and electric actuators on control units must never be con-

nected individually or between external power sources for the pur-

pose of testing, but only in connection with the control unit in ques-

tion.

It is not permitted to pull plugs off while the voltage supply is

switched on (terminal 15 "ON")! Switch the voltage supply "OFF"

first and pull out the plug.

Even with an existing polarity reversal protection incorrect polarity

must be strictly avoided. Incorrect polarity can cause damage to

control units!

Plug-in connectors on control units are only dust and water tight if

the mating connector is plugged on! Control units must be pro-

tected against spray water, until the mating connector is finally

plugged on!

Unauthorized opening of control electronics (Microcontroller MC),

modifications or repairs in the wiring can cause severe malfunc-

tions.

Do not use any radio equipment or mobile phones in the vehicle

cab without a proper aerial or in the vicinity of the control elec-

tronics!

Over the years corrosion and contamination can create high con-

tact resistances in plugs and switches, wiring looms affected by

“copper worm” (corrosion) are poor conductors. In extreme inci-

dents such a component will be absolutely dead, while minor

damage more or less reduces the performance of the affected con-

sumers to a noticeable extent.

In many cases it is enough to examine the components visually:

Green male connectors of plugs, neglected switch contacts must

be mechanically cleaned and reassembled with some contact

spray. Cables core showing green discolouration must be replaced.

A resistance measurement provides exact information about the

conductivity.

The machine has not been driven for a few days, and the battery is

almost empty? This may be caused by a “surreptitious consumer”

in the electrical network of the machine, of a leakage current

simply “draws” your battery empty. Such a leakage current can be

caused by e.g. the ignition lock, a defect switch, a relay or a

clamped or chafed cable.

A leakage current can be located by a amperage

measurement with a multimeter.

Switches, plugs, wiring looms

Leakage currents

Troubleshooting – Troubleshooting, electrical systems

BW 900-50

208

Discount-Equipment.com

order

your

parts

Summary of Contents for Bomag BW 900-50






















































































































































































































































Search results

Summary of Contents for Bomag BW 900-50

Reviews:

Brands by name

Popular brands

Fayat Bomag BW 900-50, Service Manual

Search results

Summary of Contents for Bomag BW 900-50

Reviews:

Brands by name

Popular brands