manualshive.com logo in svg

FARMSCAN Jackal v2, General Description Manual

Share
Download
FARMSCAN Jackal v2 General Description Manual Download Page 29

 

September 2015 

www.farmscanag.com 

AM-JACKAL-3 

28 

Rate Meter Setup | Solids (Generic Wizard) 

RATE METER SETUP | SOLIDS (GENERIC WIZARD) 

 
The Jackal can be configured to monitor solid products. If only one input 
is used the main screen will display the flow information in kg, lb, kg/s, 
kg/hr, T/hr, lb/s. If using the speed & area function the Jackal can also display 
kg/Ha, bu/ac, T/Ha.  

Refer to (

PAGE 31

) for Rate Monitor setup to display kg/Ha 

Sensors Required 

x

 

Shaft sensor kit (2076 Slow /2077 Fast) (2 wire) or 

x

 

Proximity sensor kit (2010P) (3 wire)

 

 

Available Connections (

PAGE 4

) 

This setup section assumes that physical wiring for the required sensors have been 
completed.   
If not please refer to 

PAGE 7

 on wiring requirements

 

SETUP 

 

1.

 

Ensure there is product in bin/tank 

2.

 

Have a bucket ready to catch the product 

3.

 

Have a set of scales (e.g. Farmscan Ag Part # 2199) ready to weigh the product 

 

 

 

 

From the front screen press 

SETUP

 

Highlight 

WIZARD

 & press 

SELECT

 

Highlight 

GENERIC WIZARD

 

& press 

NEXT

 

Highlight the 

INPUT

 number 

X: the sensor wire is 

connected into on the rear 

of the Jackal & press 

NEXT

 

 

 

 

 

Enable the input by pressing 

EDIT

 

Choose your unit of pulse. 

pulse/kg

 or 

pulse/lb

 

Highlight TARGET & press 

EDIT

 

Using the NAV buttons enter 

the target amount (kg) to be 

measured. i.e. 10.0000  

Press EXIT when done.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Jackal v2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands