FARMSCAN Jackal v2 General Description Manual Download Page 35

Page: 35 / 48

September 2015

www.farmscanag.com

AM-JACKAL-3

Air/Volt/Depth/%/Temp Pressure Sensor

AIR/VOLT/DEPTH/%/TEMP PRESSURE SENSOR

The Jackal can be configured to read & display a pressure sensor, voltage,
percentage, temperature and display:

kPa, psi, bar, Volt, %,

Sensors Required:

AA-119H or AA-119L (pressure)

Any other style that outputs a voltage. i.e. Position sensor (AA-430)
for displaying depth as a percentage (%)

Available Connections (

PAGE 4

)

This setup section assumes that physical wiring for the required sensors have been completed.
If not please refer to

PAGE 8

on wiring requirements.

CALIBRATION (MANUAL)

The example below details setting up

a LIQUID PRESSURE SENSOR

From the front screen press

SETUP

Highlight

WIZARD

& press

SELECT

Highlight

GENERIC WIZARD

press

SELECT

Highlight the

INPUT

number

(7-8)

to where the sensor

wire is connected into on the

rear of the Jackal & press

NEXT

Enable the input by pressing

EDIT

Press

EDIT

to change the

unit. kPa,psi,bar,Volt,%,

i.e. kPa

Highlight the 1

CAL HIGH

value and

EDIT

the field to

set the maximum the device

will be able to display. I.e.

600kPa. Current input

voltage of input is displayed

in the top left corner.

Using the manufactures

guide set the maximum

voltage of the sensor.

e.g. 5.000v by pressing

EDIT

NB : If manufacture values

are not available, please

refer to

PAGE 36

for further

instructions

Summary of Contents for Jackal v2

















































Search results

Summary of Contents for Jackal v2

Reviews:

Brands by name

Popular brands

FARMSCAN Jackal v2, General Description Manual

Search results

Summary of Contents for Jackal v2

Reviews:

Brands by name

Popular brands