manualshive.com logo in svg

FARMSCAN Jackal v2, General Description Manual

Share
Download
FARMSCAN Jackal v2 General Description Manual Download Page 26

 

September 2015 

www.farmscanag.com 

AM-JACKAL-3 

25 

Flow Meter Setup (Wizard) 

CALIBRATION (AUTO SET) 

1.

 

Ensure tank has water & pump is ready 

2.

 

Have a bucket ready to collect the water 

3.

 

Have a measuring device to measure the amount of liquid

 

 

 

 

 

Highlight TARGET & press 

EDIT 

Using the NAV buttons enter 

the target amount (L) to be 

measured. i.e. 20.0000  

Press EXIT when done. 

Press START, & let water flow. 

This will allow pulses from the 

flow meter to register and 

the number of pulses will be 

displayed next to 

Meas.pulses: 

When the desired test 

volume has been reached 

press STOP 

 

 

 

 

Press CALC. This will divide 

the measured amount by the 

number of pules registered.

 

MANUAL RATIO will now be 

updated to reflect the 

calibration factor.  

Press NEXT  

Using the NAV buttons select 

how you would like the UOD 

to be displayed on the front 

screen.  

Press NEXT 

You have the option to set 

Alarm Min/Max points if 
required. Using the NAV 
buttons select & EDIT as 

required. Press NEXT 

 

 

 

 

Name the input if you desire, 

Press EDIT  

or Press NEXT

 

The Wizard is now complete.  

Press NEXT 

You will be returned to the 

Setup Screen.  

Press EXIT 

Example: 1UP monitoring 

Flow Meter in L/Min

 

 

THIS ENDS THE AUTO SETUP WIZARD FOR FLOW METER  

REFER TO 

PAGE 31

 TO SETUP AS RATE MONITOR L/Ha 

 

 

Summary of Contents for Jackal v2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands