manualshive.com logo in svg

FARMSCAN Jackal v2, General Description Manual

Share
Download
FARMSCAN Jackal v2 General Description Manual Download Page 27

 

September 2015 

www.farmscanag.com 

AM-JACKAL-3 

26 

Flow Meter Setup (Wizard) 

CALIBRATION (MANUAL SET) 

 

Manual set allows for the manual input of a known pulse per pitre (PPL) factor. The pulse per litre factor can be 
obtained from the flow meter manufacture or from the plastic tag attached to the flowmeter.  

 

 

 

 

Highlight 1.000000 under 

MANUAL RATIO & press EDIT 

Using the NAV buttons enter 

the PPL factor as displayed on 

the flow meter tag. 

i.e. 91.2  

Press EXIT when done. 

Press NEXT to accept the new 

manual ratio (PPL) 

Using the NAV buttons 

select how you would like 

the UOD to be displayed on 

the front screen.  

Press NEXT 

 

 

 

 

You have the option to set 

Alarm Min/Max points if 
required. Using the NAV 
buttons select & EDIT as 

required. Press NEXT

 

Name the input if you desire, 

Press EDIT  

or Press NEXT 

The Wizard is now complete.  

Press NEXT 

You will be returned to the 

Setup Screen.  

Press EXIT 

 

 

 

 

Example: 1 UP monitoring 

Flow Meter in L/Min 

 

 

 

 

THIS ENDS THE MANUAL CALIBRATION WIZARD SETUP FOR FLOW METER 

** IT IS ADVISED TO CHECK YOUR MANUAL CALIBRATION BY MEASURING OUT A KNOWN QTY TO CONFIRM PPL** THIS 

CAN BE DONE BY COMPLETING THE CALIBRATION AUTO SET ON THE 

PREVIOUS PAGE (25)

 

 

 

Summary of Contents for Jackal v2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands