manualshive.com logo in svg

FARMSCAN Jackal v2, General Description Manual

Share
Download
FARMSCAN Jackal v2 General Description Manual Download Page 15

 

September 2015 

www.farmscanag.com 

AM-JACKAL-3 

14 

Using the Wizard 

USING THE WIZARD 

The Jackal has an inbuilt wizard function for common tasks. 

Current Wizards include easy setup for:  

a.

 

Area/Speed Wheel 

 

Wheel pickup & sensor required 

b.

 

Area/Speed GPS  

 

No Wheel Sensor required, GPS input only  

c.

 

TachoMeter  

 

 

rpm / Count (sensor required). 

There is an setting called VeryLowSpeed : for slow shaft/pulse speed when setting up shaft/pulse inputs. This is for shaft 
speeds of 1 rpm to 20 rpm. When this setting is turedn on for the input it extends the sample time and will steady the 
reading for slow rpm/pulses. If turned on for higher speed rpm/pulses the display will take longer to respond changes in 
speed.

 

d.

 

FlowMeter  

 

 

Direct readout or batch (flowmeter required) 

e.

 

Slippage Meter   

 

GPS v Wheel Input (sensor required) 

f.

 

Generic Wizard   

 

You can choose the input, screen position & calibration factors 

 

 

 

 

NB : During the wizard if you make a mistake press 

EXIT to go back one page

 

 

 

 

 

Step 1 

Press 

SETUP button

 

Step 2 

Highlight 

Wizard

 

with the UP/DOWN 

NAV buttons and 

press the 

SELECT

 

button 

Step 3 

Select the 

appropriate 

Wizard 

with the UP/DOWN 

NAV buttons and 

press the 

NEXT

 

button 

Summary of Contents for Jackal v2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands