Farm King VT3290 Operator And Parts Manual Download Page 72

Page: 72 / 232

Assembly - VT3000 Series

GANG SECTIONS

Inside Gang Sections Assembly

NOTE: The following procedure shows installing

the left front gang sections. The procedure
is correct for all gang sections.

WARNING

AVOID SERIOUS INJURY OR DEATH

•

Always install front gang sections first.

•

When installing or removing gang sections, always
securely block / support the main frame to avoid
tipping.

•

DO NOT work under suspended parts.

•

Always use lifting devices / supports of adequate
size and strength to securely support the VT3000.

Figure 109

Locate the front left, inside gang section. (Refer
to the gang section diagram for the correct
corresponding letter and orientation.)

Install straps (Item 1) around the gang section
(Item 2)

[Figure 109]

Connect the straps to an approved lifting device.

Raise and move the gang section (Item 2)

[Figure

109]

to the assembly area.

NOTE: The background has been removed from

some of the following images for picture
clarity.

Figure 110

Lower the gang section (Item 1)

[Figure 110]

onto

the ground in front of the left main frame.

Remove strap (Item 2)

[Figure 110]

from the lifting

device.

NOTE:

Do not remove straps (Item 3) from around
the gang section (Item 1)

[Figure 110]

Figure 111

Route straps (Item 1)

[Figure 111]

in front and

behind the gang beam, straddling in the gang
beam.

Connect the straps to an approved lifting device.

Raise the gang section and move inner blade
towards the center of the main frame. Lower gang
section to the ground.

Summary of Contents for VT3290









































































































































































































































Search results

Summary of Contents for VT3290

Reviews:

Farm King VT3290, Operator And Parts Manual, Page: 72 / 232

Search results

Summary of Contents for VT3290

Reviews: