Farm King VT3290 Operator And Parts Manual Download Page 43

Page: 43 / 232

Assembly - VT3000 Series

Wing Rockshaft Hydraulic Cylinders Assembly

Figure 63

Locate the RH 4” x 24” hydraulic cylinder (Item 1)

[Figure 63]

and LH 3-1/2” x 24” hydraulic cylinder

Install a strap (Item 2)

[Figure 63]

around the

hydraulic cylinder.

Connect the strap to an approved lifting device.

Raise and move the hydraulic cylinder to the
assembly area.

Figure 64

Locate the two eye bolt rods (Item 1) and four
1-1/4” (Grade 2) nuts (Item 2)

[Figure 64]

Thread one 1-1/4” nut on the eye bolt rod. Thread
the nut on approximately two inches from the eye.

Figure 65

Install one eye bolt rod through the mount (Item
1) on the RH wing (rear). Install second 1-1/4” nut
(Item 2)

[Figure 65]

. Do not tighten at this time.

Repeat for LH wing rockshaft cylinder.

Figure 66

Align RH 4” x 24” wing rockshaft cylinder (Item
1) (ports facing up) with the RH wing mounting
bracket & eye-bolt rod (Item 2)

[Figure 66]

Install one washer (Item 3) and cylinder pin (Item
4)

[Figure 66]

through the RH wing lift cylinder

and mounting plate. Install two 5/16” x 1-3/4”
cotter pins.

Repeat for LH 3-1/2” x 24” wing rockshaft cylinder.

Loosen / remove port plugs to allow the cylinder
rod to be extended.

Summary of Contents for VT3290









































































































































































































































Search results

Summary of Contents for VT3290

Reviews:

Farm King VT3290, Operator And Parts Manual, Page: 43 / 232

Search results

Summary of Contents for VT3290

Reviews: