manualshive.com logo in svg

Farm King VT3290, Operator And Parts Manual, Page: 108 / 232

Share
Download
Farm King VT3290 Operator And Parts Manual Download Page 108

Operation - VT3000 Series

106

Leveling

Check Factory Setting on Leveling Crank

Figure 162

Check the following dimensions on the leveling 
crank.

Front crank pivot to rockshaft crank pivot length 
(Item 1) 

[Figure 162]

:

•  VT3290 & VT3320 – 51-1/2”
•  VT345 & VT375 – 51”

Spring pre-compress length (Item 2) 

[Figure 162]

:

•  VT3290 & VT3320 – 16-1/2”
•  VT3345 & VT3375 – 15”

Front to Back

Move to the operator’s position.

Park the tractor / equipment on a flat level surface.

Unfold wings so blades are 2” to 3” (51 mm to 76 
mm) off the ground.

Stop the tractor and leave the operator’s position. 

IMPORTANT

This notice identifies procedures which must be 
followed to avoid damage to the machine.

Figure 163

Loosen jam nut (Item 1) 

[Figure 163]

 on leveling 

link.

NOTE: One full turn of the adjusting nut will raise 

/ lower the machine approximately 1-3/8”.

Tighten adjustment nut (Item 2) 

[Figure 163]

 to 

lower the front. Back off adjustment nut to raise 
the front.

Tighten jam nut (Item 1) 

[Figure 163]

 when front 

blades and rear blades are an equal distance off 
the ground.

NOTE: Lowering the machine may make adjusting 

easier.

NOTE: Level machine after changing tractor 

drawbar height.

1

1

2

2

2

Summary of Contents for VT3290









































































































































































































































Reviews:

No comments