manualshive.com logo in svg

Farm King VT3290, Operator And Parts Manual, Page: 103 / 232

Share
Download
Farm King VT3290 Operator And Parts Manual Download Page 103

Operation - VT3000 Series

101

TRACTOR REQUIREMENTS

WARNING

AVOID SERIOUS INJURY OR DEATH

The tractor must be equipped with an approved 
Roll Over Protection Structure (ROPS) and safety 
belts to help prevent personal injury or death 
caused by tractor roll over.

WARNING

• 

Keep shields and all guards in place.

• 

Keep away from moving parts.

• 

Keep bystanders away.

NOTE: The following information will depend on 

tilling depth, soil type, field speed, etc.

8 in. (203 mm) Spacing

The VT3000 with 8 in. (203 mm) spacing will 
require a tractor with minimum 8.0 to 12.0 DBHP/
foot (6.0 to 9.0 kW per 305 mm).

9 in. (230 mm) Spacing

The VT3000 with 9 in. (230 mm) spacing will 
require a tractor with minimum 8.0 to 12.0 DBHP/
foot (6.0 to 9.0 kW per 305 mm).

CAUTION

Using a tractor with greater HP than the 
recommended range may cause severe damage 
to frame and / or gang components of implement 
and thereby void warranty.

Drawbar Adjustment

NOTE: Tractor must be equipped with a clevis type 

drawbar to pull the VT3000.

Figure 157

Adjust the tractor’s drawbar in / out, until the 
center of the hitch pin hole (Item 1) 

[Figure 157]

is 16 in. (410 mm) from the end of the tractor’s 
PTO shaft. See your tractor’s owner’s manual for 
correct adjustment procedures.

1

Summary of Contents for VT3290









































































































































































































































Reviews:

No comments