Farm King VT3290 Operator And Parts Manual Download Page 106

Page: 106 / 232

Operation - VT3000 Series

104

Connecting Hydraulic Lines

WARNING

HIGH PRESSURE FLUID HAZARD

To prevent serious injury or death from high
pressure fluid:

•

Relieve pressure on system before repairing or
adjusting.

•

Wear proper hand and eye protection when searching
for leaks. Use wood or cardboard instead of hands.

•

Keep all components in good repair.

IMPORTANT

Contain and dispose of any oil leakage in an
environmentally safe manner.

Thoroughly clean the quick couplers before
making connections. Dirt can quickly damage the
system.

NOTE: Make sure the quick couplers are fully

engaged. If the quick couplers do not fully
engage, check to see that the couplers are
the same size and type.

To Connect:

Figure 160

Connect the hydraulic lines to the tractor:

• Raise / Lower, Green Ties (Item 1)

[Figure 160]

• Fold / Unfold, Blue Ties (Item 2)

[Figure 160]

To Disconnect:

WARNING

AVOID BURNS

Hydraulic fluid, tubes, fittings and quick couplers
can get hot when running equipment. Be careful
when connecting and disconnecting quick
couplers.

Pull on the hydraulic lines to disconnect.

Connect Electrical Harness

Connect the VT3000’s lighting harness to the
tractor’s electrical system.

Summary of Contents for VT3290









































































































































































































































Search results

Summary of Contents for VT3290

Reviews:

Farm King VT3290, Operator And Parts Manual, Page: 106 / 232

Search results

Summary of Contents for VT3290

Reviews: