Farm King VT3290 Operator And Parts Manual Download Page 42

Page: 42 / 232

Assembly - VT3000 Series

Figure 60

Install pin (Item 1). Install one 5/16” x 1-3/4” cotter
pin (Item 2)

[Figure 60]

Remove the strap.

Installing Wing Lift Cylinders

Figure 61

Locate the four 5” x 36” wing lift hydraulic
cylinders (Item 1)

[Figure 61]

Install a strap (Item 2)

[Figure 61]

around one

hydraulic cylinder.

Connect the strap to an approved lifting device.

Raise and move the hydraulic cylinder to the
assembly area.

Repeat for remaining three cylinders.

Figure 62

Align LH front wing lift cylinder (Item 1) (ports
facing back) with the left hole on the mounting
plate (Item 2)

[Figure 62]

located at the rear of the

LH main frame.

Install one cylinder pin (Item 3)

[Figure 62]

through

the RH wing lift cylinder and mounting plate.
Install one 5/16” x 1-3/4” cotter pin.

Place blocks (Item 4) under the LH wing lift cylinder
(Item 1)

[Figure 62]

Lower LH wing lift cylinder onto the block and
remove strap.

Repeat procedure for remaining wing lift cylinders.

Summary of Contents for VT3290









































































































































































































































Search results

Summary of Contents for VT3290

Reviews:

Farm King VT3290, Operator And Parts Manual, Page: 42 / 232

Search results

Summary of Contents for VT3290

Reviews: