Falcon E3840 Installation, Servicing And User Instructions Manual Download Page 6

IMPORTANT INFORMATION

 

ELECTRICAL SAFETY AND ADVICE REGARDING SUPPLEMENTARY ELECTRICAL PROTECTION 

Commercial kitchens and foodservice areas are environments where electrical appliances may be located 
close to liquids, or operate in and around damp conditions or where restricted movement for installation and 
service is evident. 

The  installation  and  periodic  inspection  of  the  appliance  should  only  be  undertaken  by  a  qualified,  skilled 
and competent electrician; and connected to the correct power supply suitable for the load as stipulated by 
the appliance data label. 

The  electrical  installation  and  connections  should  meet  the  necessary  requirements  to  the  local  electrical 
wiring regulations and any electrical safety guidelines. 

We recommend:- 

Supplementary electrical protection with the use of a type A residual current device (RCD)

Fixed wiring appliances incorporate a locally situated switch disconnector to connect to, which is easily
accessible  for  switching  off  and  safe  isolation  purposes.  The  switch  disconnector  must  meet  the
specification requirements of IEC 60947.

Your attention is drawn to:- 
BS 7671:2018

–Guidance Note 8 - 8.13 : Other locations of increased risk 

It is recognized that there may be locations of increased risk of electric shock other than those specifically 
addressed  in  Part  7  of  BS  7671.  Examples  of  such  locations  could  include  laundries  where  there  are 
washing  and  drying  machines  in  close  proximity  and  water  is  present,  and  commercial  kitchens  with 
stainless steel units, where once again, water is present.  

Where  because  of the  perception  of  additional  risks  being  likely,  the  installation  designer  decides  that  an 
installation or location warrants further protective measures, the options available include: 

Automatic  Disconnection  of  Supply  (ADS)  by  means  of  a  residual  current  device  having  a  residual
operating current not exceeding 30mA;

Supplementary protective equipotential bonding; and

Reduction of maximum fault clearance time.

The provision of RCDs and supplementary bonding must be specified by the host organization’s appointed 
installation  designer  or  electrical  contractor  and  installed  by  a  suitably  qualified  and  competent  electrician 
so as to comply with Regulations 419.2 and 544.2 

Summary of Contents for E3840






































Reviews: