Falcon E3840 Installation, Servicing And User Instructions Manual Download Page 15

11 

 

3.0  SERVICING AND CONVERSION 

 

SERVICE INFORMATION 

This unit carries an extensive mainland UK warranty. The warranty is in addition to and does not 
change your statutory or legal rights.  

The warranty policy can be found on our website which details the conditions of the warranty and 
the exclusions.  

https://www.falconfoodservice.com/info-centre/policy

  

 

 

Service calls to equipment under warranty will be carried out in accordance with the conditions of 
sale.  

Warranty calls can be made between 8:30 am and 5:00 pm weekdays only. 

To ensure your warranty enquiry is handled as efficiently as possible, ensure you have the following 
appliance information prior to calling us: 

1.  Model number 

– found on data plate  

2.  Serial number 

– found on data plate 

3.  Brief description of the issue 

 

To contact Falcon for a warranty issue dial (UK only) 01786 455 200 and select Warranty Issues from 
the menu. 

 

 

BEFORE ATTEMPTING ANY SERVICING, TURN OFF  GAS  SHUTOFF  VALVE  AND 
ELECTRICAL  SUPPLY.  TAKE STEPS TO ENSURE THAT THESE CANNOT BE 
INADVERTENTLY TURNED ON. 
 
AFTER ANY MAINTENANCE TASK, CHECK UNIT TO  ENSURE  THAT  IT 
PERFORMS  SAFELY  AND  CORRECTLY AS DESCRIBED IN SECTION 2.4. 

 

MAINTENANCE CHECK  
Regular servicing of the appliance should be undertaken to ensure correct 
operation, it is functioning as intended, and safe to use. We recommend servicing 
after 2,500 hours of use, or annually, whichever comes first.  
Any maintenance schedule should be carried out in accordance with SFG20 
Maintenance Schedules. Should any issues with the integrity of the components 
be identified these should be replaced. If the appliance is not considered safe the 
unit should be removed from service and the responsible person advised why the 
unit is not safe to use and what remedial action is needed. Contents of the 
maintenance schedule should be agreed with the maintenance provider. 
 

 

Moving the fryer with hot or cold oil in fry pot can be dangerous. Scalding could occur. Spilled oil 
or fat on the kitchen floor could cause slipping accidents and any such deposit should be 
cleaned up straight away. 
To prevent any such hazard, caution must be observed when moving fryer. 

Summary of Contents for E3840






































Reviews: