background image

 

33 

Long   Term   Battery   Storage:   

   
When   storing   your   Falco   e-­‐Motors   battery   for   more   than   2   months,   please   
follow   the   instructions   below:   
   

Ø

It   is   recommended   that   Li-­‐ion   battery   packs   are   charged   between   70%   %   
80%   before   a   long   storage   period.   

Ø

Store   in   a   10C   to   25C   area.   

Ø

The   most   preferable   storage   temperature   is   20c.   

Ø

Avoid   long   periods   of   storage   when   temperatures   reach   45C   or   higher   

Ø

Avoid   direct   exposure   to   sunrays   and   heat   when   storing   a   battery   pack   in   
a   warehouse.   

Ø

Keep   away   from   extreme   temperature   changes.   

Ø

Keep   away   from   condensation.   

Battery   Charging   Procedure:   

   

A full charge will take approximately 4 hours. 

   

Ø

Make   sure   that   the   battery   ON/OFF   button   is   set   to   OFF.   

Ø

Plug   the   mains   adapter   into   the   mains   socket   outlet   and   switch   on.   

Ø

Gain   access   to   the   charging   socket   on   the   battery   by   lifting   the   
protective   cover.   

Ø

Connect   the   plug   on   the   lead   of   the   battery   charger   to   the   socket   on   
the   battery.   

Ø

The   light   on   the   charger   will   show   red   when   charging   and   will   turn   to   
green   when   fully   charged.   

Note: 

The mains adapter and battery can become warm when charging, this is normal. 

Summary of Contents for Intelligent energy management system



































Reviews: