Falco e-motors Intelligent energy management system Installation Manual And Owner'S Manual Download Page 22 | Manualshive

Page: 22 / 34

Falco e-motors Intelligent energy management system Installation Manual And Owner'S Manual Download Page 22

22

Hx DISPLAY CONSOLE FEATURES

Key 1
(mode)

Changes mph/kph, Manual pairing of motor and console, clock/odometer
selector, moves cursor when entering data

Key 2

Power level increase, Clock setting, Data entry

Key 3

Power level decrease, Wheel size setting

Key4

(heart)

Manual pairing of heart rate monitor, turns on/off console back-‐light turns

on/off Turbo Mode

Segment 1

Displays battery voltage. Heart Rate (requires ANT+ heart rate monitor),
Motor ID, Console/Motor pairing status.

Segment 2

Restricted or Cruise speed setting indicator.

Segment 3

Speed indicator, mph/kph

Segment 4

Odometer & clock display. Wheel size &Clock setting

Segment 5

Turbo Mode indicated on/off

Segment 6

Regeneration indicator

Segment 7

Power level Indicator -‐5 to +5

Segment 8

Assistance indicator

Segment 9

Lock Mode

«
...
20
21
22
23
24
...
»

Summary of Contents for Intelligent energy management system



































Reviews:

No comments