CNC8070
R
EF
. 0402
E
RROR
SOLUTIONS
Page 71 of 128
Errors 1000-1999
1818
'J = 0'
DETECTION
Executing a multiple machining cycle (G160-G165).
CAUSE
The J parameter (ordinate pass between machining operations) has been
programmed with a 0 value in a multiple machining cycle.
SOLUTION
Assign a correct value to the cycle parameter.
1819
'K = 0'
DETECTION
Executing a multiple machining cycle (G160-G165).
CAUSE
The K parameter (number of machining operations) has been programmed with a 0
value in a multiple machining cycle.
SOLUTION
Assign a correct value to the cycle parameter.
1820
'Two of parameters X, I and K must be programmed'
DETECTION
Executing a multiple machining cycle (G160-G165).
CAUSE
In a multiple machining cycle, two of the following parameters have not been
programmed: X (length), I (machining pass), K (number of machining operations).
SOLUTION
Assign a correct value to the cycle parameter.
1821
'B must be multiple of I'
DETECTION
Executing a multiple machining cycle (G164).
CAUSE
The I parameter (machining pass) must be contained an entire number of times in
B (angular travel).
SOLUTION
Assign a correct value to the cycle parameter.
1822
'The Y parameter must be multiple of the J parameter'
DETECTION
Executing a multiple machining cycle (G160-G165).
CAUSE
The J parameter (machining pass) must be contained an entire number of times in
Y (length in ordinates).
SOLUTION
Assign a correct value to the cycle parameter.
1823
'Two of parameters Y, J and D must be programmed'
DETECTION
Executing a multiple machining cycle (G160-G165).
CAUSE
In cycles G161 and G162, two of the following parameters have not been
programmed: Y (length in ordinates), J (machining pass), D (number of machining
operations).
SOLUTION
Assign a correct value to the cycle parameter.
1824
'One of parameters I and K must be programmed'
DETECTION
Executing a multiple machining cycle (G160-G165).
CAUSE
One of the these two parameters have not been programmed, I (machining pass),
K (number of machining operations).
SOLUTION
Assign a correct value to the cycle parameter.
1825
'One of parameters I and A must be programmed'
DETECTION
Executing the multiple machining cycle (G165).
CAUSE
One of the these two parameters have not been programmed, I (angular pass), A
(number of machining operations).
SOLUTION
Assign a correct value to the cycle parameter.
1826
'Parameter I multiplied by K must be equal to 360'
DETECTION
Executing a multiple machining cycle G163.
CAUSE
In a multiple machining in circle (G163), the pass (I) multiplied by the number of
machining operations (K) is not equal to 360º.
SOLUTION
Assign a correct value to the cycle parameter.
1827
'Parameters X and Y are equal to 0'
DETECTION
Executing a multiple machining cycle (G163-G165).
CAUSE
The parameters defining the center of the arc of the multiple machining have been
programmed with a value of 0.
SOLUTION
Assign a correct value to the cycle parameter.
Summary of Contents for CNC8 070
