6
J6
J12
J5
J11
J14
J7
+
-
F
SW1 SW2 SW3
J15
J1
J2
J3
J4
M2 M1A
M1
DL1 DL2
DL10
DL11
DL12
DL13
DL14
DL18
DL17
DL5
DL6
DL9
DL3
DL4
DL15
2Easy BUS
OPEN
CLOSE
FSW STOP
EMR
GND
+24
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
2 2
+24
+24
+24
+24
OUT1
OUT2
OUT3
Re
la
y N
O
GND
LAMP
LOOP 1
LOOP 2
MOTOR
POWER
BATTERY
ENCODER
DISP1
DL7
DL8
DL16
M
SW4
1 2
2 2
4 5 6 7
Re
la
y N
O
Re
la
y C
O
M
J13
J16
SW5
J10
OUT5
OUT6
Fig. 1
Fig. 1
ENGLISH
E680 CONTROL BOARD
DISP1
Signalling/Programming display
DL1
BUS Device status
DL2
BUS status (see paragraph 5.3)
DL3
LOOP 1 status
DL4
LOOP 2 status
DL5
Board failure signal
DL6
Not used
DL7
Encoder status
DL8
Not used
DL9
Board power supply present
DL10
OPEN input status LED
DL11
CLOSE input status LED
DL12
FSW input status LED
DL13
STOP input status LED
DL14
EMR input status LED
DL15
Released bar signal
DL16
Battery power signal
DL17
Radio channel 1 activity
DL18
Radio channel 2 activity
J1
Input signal connector
J2
Digital output connector
J3
Signalling lamp connector
J4
Detection loop connector
J5
Motor connector
J6
BUS 2Easy connector
J7
Beam movement encoder connector
J10
Connector for Minidec / RP / Decoder radio board
J11
Released bar detection connector
J12
Emergency battery connector
J13
Continuous power voltage connector
J14
USB connector for firmware upgrade
J15
Integrated flashing
traffic light connector
SW1
Programming key “F”
SW2
Programming key “+”
SW3
Programming key “-”
SW4 /SW5
LOOP 1 / LOOP 2 calibration button
M1/M1A/M2
Optional module connector (Connectivity):
1. WARNINGS
Warning - Before carrying out any work on the control board
(connections, maintenance, etc.) always:
•
cut off the electrical power;
•
install a differential magnetothermic switch with a suitable
activation threshold upstream from the system;
•
always separate the power cables from the control and safety
cables (button, receiver, photocells, etc.);
•
avoid any electrical disturbance using separate sheaths or a
shielded cable (with the shield connected to the earth).
2. DESCRIPTION OF THE COMPONENTS
Mains power
voltage
100-240 V~ +6% -10%
connected to switching power supply
Continuous
power voltage
36 V
"
Absorbed power
240W
Accessories
power supply
24 V
"
Max accessories
current
800 mA
Operating ambient
temperature
from -20°C to +55°C
Protection fuses
4 self-restoring
Pause time
Programmable (from 0 seconds to 4.1
minutes)
3. TECHNICAL SPECIFICATIONS
Work time
Programmable (from 0 to 4 minutes)
Motor power
Programmable on 50 levels
Motor speed
Programmable on 10 levels
Programmability
3 configuration levels for greater flexibility
of use
Rapid connector
1 5-pin connector for Minidec radio board,
Decoder, RP/RP2
Programmable
outputs
4 programmable outputs in 19 different
functions
Specifications
Deceleration management, encoder,
multi-function display, BUS technology
and BUILT-IN METAL MASS DETECTOR
Summary of Contents for B680
