FAAC B680, Manual

Page: 17 / 42

15
ENGLISH
05
When this function is activated, the OPEN command during opening will stop movement.
If parameter
06
is
no
the system is ready for opening.
If parameter
06
is
Y
the system is ready for closing.
Y
= when opening it stops
no
= disabled
06
When this function is activated, the OPEN command during opening reverses movement.
If parameters
05
and
06
are
no
OPEN will have no effect during opening.
Y
= when opening it reverses
no
= disabled
07
When this function is activated, the OPEN command during pause stops operation.
If parameters
07
and
08
are
no
OPEN resets the pause time
Y
= when in pause it stops
no
= disabled
08
When this function is activated, the OPEN command during pause causes closing.
If parameters
07
and
08
are
no
OPEN resets the pause time.
Y
= when in pause it closes
no
= disabled
09
When this function is activated, the OPEN command during closing stops operation,
otherwise it reverses movement.
Y
= stops
no
= reverses
10
Activation of DEAD-MAN closing (command always pressed). Releasing the CLOSE
command will stop operation
Y
= active
no
= disabled
11
When this function is activated, the CLOSE command has priority over OPEN, otherwise
OPEN has priority over CLOSE.
Y
= active
no
= disabled
12
When this function is activated, the CLOSE command commands closing when released.
As long as CLOSE is activated, the unit stays in closing pre-fl ashing.
Y
= closes when released
no
= closes immediately
13
When this function is activated, the CLOSE command during opening stops operation,
otherwise the CLOSE command commands reverse immediately or when opening is com-
pleted (see also parameter
14
)
Y
= CLOSE stops
no
= CLOSE reverses
14
When this function is activated, and if parameter
13
is
no
, the CLOSE command commands
immediate closing at the end of the opening cycle (stores CLOSE). If parameters
13
and
14
are
no
CLOSE commands immediate closing.
Y
= closes at the end of
opening
no
= immediate closing
15
When this function is activated, with the system blocked by a STOP, a next OPEN
moves in the opposite direction. If parameter
15
is
no
it always closes.
Y
= moves in the opposite
direction
no
= always closes
16
When this function is activated, during closing, the CLOSING SAFETIES stop and allow
motion to resume when they are disengaged, otherwise they immediately reverse opening.
Y
= closes when disengaged
no
= immediate reverse
17
When this function is activated, the CLOSING SAFETIES command closing when they are
disengaged (see also parameter
18
).
Y
= closing when FSW
is disengaged
no
= disabled
18
When this function is activated, and if parameter
17
is
Y
, the unit will wait for the
opening cycle to end before executing the closing command provided by the
CLOSING SAFETIES .
Y
= closes at the end of
opening
no
= disabled
19
When this function is activated, during closing, LOOP2 stops and allows motion to resume
when it is disengaged, otherwise it immediately reverses opening.
Y
= closes when disengaged
no
= immediate reverse
20
When this function is activated, LOOP2 commands closing when it is disengaged (see also
parameter
21
).
Y
= closes if LOOP2 is clear
no
= disabled
21
When this function is activated, and if parameter
20
is
Y
, the unit will wait for the opening
cycle to end before executing the closing command provided by LOOP2.
Y
= closes at the end of
opening
no
= disabled
22
When this function is activated: in case of a blackout, once electrical power has been
restored, if an OPEN command is not active the automated system recloses immediately.
Y
= active
no
= disabled
23
LOOP 1 commands opening and, once completed, it closes if disengaged (useful in case
of vehicle backing-up with consecutive loops). If disabled, when LOOP 1 is disengaged, it
does not close.
Y
= closes if LOOP1 clear
no
= disabled
24
When this function is activated, an open or close command is only carried out after
the safeties have been disengaged.
Y
= active
no
= disabled
25
A.D.M.A.P. function
When this function is activated, the result is operation of safeties compliant with French
regulations.
Y
= active
no
= disabled
26
When this function is activated, the CLOSING SAFETIES during closing stop and reverse
movement when they are disengaged, otherwise they reverse immediately.
Y
= stops and reverses when
disengaged.
no
= reverses immediately.
27
DO NOT CHANGE
no
28
DO NOT CHANGE
no
29
DO NOT CHANGE
no
30
When this function is activated, the LOOP1 commands are prioritised rather than the
LOOP2 commands.
Y
= active
no
= disabled