Eurotherm 346 Installation And Operation Manual Download | Manualshive

Page: 43 / 192

background image

HA243820
Issue 5 Mar 98

Section 3

Page 3 - 19

MODEL 346 INSTALLATION AND OPERATION MANUAL

3.3.3 OPERATOR MENU (Cont.)

ALARM CONFIGURATION

Note...

This display appears only if alarm access has been defined as operator accessible in the instrument configu-

ration (section 4.9).

If the alarm configuration has been defined as operator accessible, then the user can carry out a full alarm
configuration. Refer to section 4.10 for full details

BATCH NUMBER

Batch Number

123456

The up/down/side arrow keys are used to define up to six alpha-numeric characters (following the fixed letter
‘B’) that are to be printed with the Time Header. The Time Header is printed on Power-up, as the first line of
the Log and once in each sequence of Printed Scales.

LOG INITIATION

Print Log ?

The ENTER key is operated to call the Log up for printing.

Print Log ?

ENTER to confirm

The ENTER key is operated again to initiate the printing of the Log. Once started the Log will continue until it is
complete. If other actions (such as a chart speed change) occur during the printing of the Log, a line is drawn
across the chart to mark the time. Any printing called for by those actions will be delayed until after the Log.

VIEW TIMER

View Timer?

N

The Up and Down arrow keys are used to select Timer 1 to 4 for access. Operation of the Enter key calls the
selected timer’s configuration to the display. The configuration can be viewed but not altered. See section
4.12 for details on timer functions.

Timer N

13:00 31 JAN90

Operation of the Clear key returns the operator to the menu.

RANGE MAGNIFY

Range Magnify

Off

The up/down arrow keys to turn the Range Magnify function ON or OFF.

«
...
41
42
43
44
45
...
»

Summary of Contents for 346

































































































































































































Reviews:

No comments

Related manuals for 346

Brand: Tascam Pages: 12

Brand: Tascam Pages: 46

Brand: Tascam Pages: 120

Brand: Tascam Pages: 124

Brand: Tascam Pages: 96

Brand: Tascam Pages: 2

Brand: Tascam Pages: 2

Brand: Tascam Pages: 8

Brand: Omega Pages: 20

Brand: EDIC-mini Pages: 8

Brand: Tascam Pages: 62

Brand: Panasonic Pages: 14

Brand: Olympus Pages: 104

Brand: Samsung Pages: 22

Brand: Magnavox Pages: 83

Brand: Olympus Pages: 10

Brand: THOMSON Pages: 2

Brand: Lawmate Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands