Epson AcuLaser C2000 Administrator'S Manual Download Page 72

Page: 72 / 272

3-38

Settings for NetWare

For Remote (rpinter on IPX), go to the next section “Configuring
for NetWare using EpsonNet WinAssist” on page 3-38.

For Remote (LPR on IP), go to “Setting the IP Address Using
EpsonNet WinAssist/MacAssist” on page 2-8.

For Queue Based, go to “Using Bindery Print Server (NetWare
3.1x/4.1x)” on page 3-6 or “Using NDS Print Server (NetWare
4.1x/5)” on page 3-11.

Configuring for NetWare using EpsonNet
WinAssist

Follow the steps below if the printer is a Remote (rprinter on IPX)
connection.

Note:

Be sure that the one of the following Client is installed in your computer;
Novell Client 32, Novell IntranetWare Client, or Novell Client.

1. Turn on the printer.

2. From any NetWare client, log in to the target NetWare server

as ADMIN.

3. Run EpsonNet WinAssist from the Start menu.

Summary of Contents for AcuLaser C2000

















































































































































































































































































Search results

Summary of Contents for AcuLaser C2000

Reviews:

Related manuals for AcuLaser C2000

Brands by name

Popular brands

Epson AcuLaser C2000, Administrator'S Manual

Search results

Summary of Contents for AcuLaser C2000

Reviews:

Related manuals for AcuLaser C2000

Brands by name

Popular brands