Epson AcuLaser C2000 Administrator'S Manual Download Page 240

Page: 240 / 272

13-4

Printer Status Page

The environmental requirements for Printer Status Page are;

Server and client

❏

Internet Information Service (IIS) is installed in Windows
2000. To check whether IIS is installed, double-click the

Add/Remove Programs

icon in the Control Panel, click the

Add/Remove Windows Components

button, and then

click the

Components

button. In the Windows Components

dialog box, make sure the

Internet Information Service (IIS)

is selected.

❏

Internet Explorer 4.01 or better installed.

❏

The computer is connected to the network and TCP/IP is
correctly set.

Printer

You need to set up the printer that you want to manage with
Printer Status Page.

1. Make sure the printer is connected to the network, and

TCP/IP is correctly set for the printer.

2. Install the printer driver using the Add Printer wizard. When

you install the EPSON printer driver for Windows 2000,
Printer Status Page is also installed. See “Printing via
Standard TCP/IP Port Monitor in Windows 2000” on page
5-3 and the following notes to install the printer driver.

Note:

❏

Install printer drivers using the Add Printer wizard. Do not
install using Setup.exe because the Printer Status Page is not
installed in this way.

❏

Use Standard TCP/IP Port Monitor for the port.

❏

When the Printer Sharing dialog box appears during
installation, select

Share as

Summary of Contents for AcuLaser C2000

















































































































































































































































































Search results

Summary of Contents for AcuLaser C2000

Reviews:

Related manuals for AcuLaser C2000

Brands by name

Popular brands

Epson AcuLaser C2000, Administrator'S Manual

Search results

Summary of Contents for AcuLaser C2000

Reviews:

Related manuals for AcuLaser C2000

Brands by name

Popular brands