REV. 05/2020
ELECTRICAL SYSTEM
9
128
Parameters
Description
Remark
KEY VOLTAGE
Voltage value with 1 decimal digit. Key
voltage value measured at the key on.
BATTERY VOLTAGE
Voltage value with 1 decimal digit. Battery
voltage value measured at the key on.
MOTOR VOLTAGE
Percentage value. It is the voltage generated
by the inverter expressed in percent of the
actual battery voltage. 100% means the sine
wave width is close to the actual battery
voltage; 0% means the sine wave width is
null.
FREQUENCY
Hz value. This is the frequency of the sine
waves the inverter is supplying.
ENCODER
Hz value. This is the speed of the motor
measured with the encoder and expressed in
the same unit of the FREQUENCY reading.
SLIP VALUE
Hz value. This is the slip between the
frequency and the speed of the motor
(SLIP VALUE = FREQUENCY-ENCODER).
CURRENT RMS
Ampere value. Root Mean Square value of
the line current in the motor.
ID FILTERED RMS
Ampere value. Root Mean Square value of
the current in d axle.
IQ FILTERED RMS
Ampere value. Root Mean Square value of
the current in q axle.
IQ IMAX LIMIT
Ampere value. Root Mean Square maximum
value of the current in q axle according to
parameters set.
MOT. POWER WATT
Watt value. Estimated power supplies to the
motor.
FLUX WB/1000
Wb value. Estimated flux into the motor.
MOTION TORQUE
Nm value. Estimated motion torque value.
BATTERY CHARGE
Percentage value. It supplies the residual
charge of the battery as a percentage of the
full charge level.
TEMPERATURE
°C value. This is the temperature of the
inverter base plate. This temperature
is used for the HIGH TEMPERATURE alarm
detection.
Traction Controller (ACE3)
Summary of Contents for CPD30L1-B
