EnGenius ECB-3220 User Manual Download Page 42

Page: 42 / 51

11g Wireless Client Bridge/AP

Version 1.36

You can arrange the different data rate in distance in Access Point mode. Please

refer below table.

6M-24M

36M 48M 54M

High

Great

Ultra High

Great

N/A

Super

Great

N/A

Extreme

Great

N/A

Preamble Type

: For best performance, all devices on the wireless network should

use the same preamble type. However, the wireless network will still function even
though the wrong preamble type is used.

Broadcast SSID

: This is a security feature that is enabled by default. This allows

clients on the wireless network to run a site survey and detect this Access Point.
Select

Disabled

if you do not want this Access Point detected in a site survey.

IAPP

: It is recommended to

Enable

the Inter-Access Point Protocol (IAPP) if you

would like the clients on the wireless network to seamlessly roam between Access
Points of the same SSID.

802.11g Protection

: If your wireless network is using both 802.11b and 802.g

devices then it is recommended to enable this feature so that the 802.11b devices
will not degrade the performance of 802.11g devices.

User Isolation

: Click “

Enabled

” to stop packet transmission between Wireless

Clients.

Turbo Mode

: Select “

Enable

” to activate the Turbo mode for better performance.

The Default is disabled.

Click

the

Apply Changes

button to confirm the changes. This device will

automatically restart once these changes have been applied.

5.4.3 Security

Click

the

Security

link under the

Wireless

menu. On this page you can configure

the authentication and encryption settings such as WEP, WPA, and 802.1x.

Summary of Contents for ECB-3220




















































Search results

Summary of Contents for ECB-3220

Reviews:

Related manuals for ECB-3220

Brands by name

Popular brands

EnGenius ECB-3220, User Manual

Search results

Summary of Contents for ECB-3220

Reviews:

Related manuals for ECB-3220

Brands by name

Popular brands