manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 112 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 112

Commissioning

Proline Promag P 500 HART

112

Hauser

10.4.10   Configuring empty pipe detection

The 

Empty pipe detection

 submenu contains parameters that must be configured for the

configuration of empty pipe detection.

Navigation

"Setup" menu → Empty pipe detection

‣

Empty pipe detection

Empty pipe detection

→   112

New adjustment

→   112

Progress

→   112

Switch point empty pipe detection

→   112

Response time empty pipe detection

→   112

Parameter overview with brief description

Parameter

Prerequisite

Description

Selection / User
interface / User

entry

Factory setting

Empty pipe detection

–

Switch empty pipe detection on
and off.

• Off
• On

Off

New adjustment

The 

On

 option is selected in

the 

Empty pipe detection

parameter.

Select type of adjustment.

• Cancel
• Empty pipe adjust
• Full pipe adjust

Cancel

Progress

The 

On

 option is selected in

the 

Empty pipe detection

parameter.

Shows the progress.

• Ok
• Busy
• Not ok

–

Switch point empty pipe detection

The 

On

 option is selected in

the 

Empty pipe detection

parameter.

Enter hysteresis in %, below
this value the measuring tube
will detected as empty.

0 to 100 %

10 %

Response time empty pipe detection In the 

Empty pipe detection

parameter (→   112), the 

On

option is selected.

Enter the time before
diagnostic message S862 ''Pipe
empty'' is displayed for empty
pipe detection.

0 to 100 s

1 s

10.4.11   Configuring the HART input

Navigation

"Setup" menu → HART input

‣

HART input

Capture mode

→   113

Device ID

→   113

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments